Arduino Fans

High Quality Arduino Nano V3.0 ATMega328P-AU Ch340G USB UART Converter On-board 3.3v regulator IC Pre-Installed Bootloader 14 Digital input / output ports 8 analog inputs ports and 6 PWM output ports Micro USB connector for Power and Download

• 100% New High Quality Pro Mini ATMega328P-AU Board
• Using Original Atmel ATMega328P-AU Microcontroller 5V 16Mhz
• 14 Digital input/output ports RX and TX, D2 ~ D13
• 8 Analog input ports A0 ~ A7
• 6PWM ports, D3, D5, D6, D9, D10, D11
• Support external 3.3 V ~ 12 V DC power supply
• Support 9 v batteries
• Max 150mA output
• Weighs less than 2 grams!
• Size: 3.3cm x 1.6cm (33mm x 16mm)

• 100% New High Quality Digispark LilyPad
• Using Original ATMEL ATTiny85 Microcontroller
• 8 Kb Programmable ISP Flash Memory
• 512 Bytes SRAM and 512 Bytes Data EEPROM / HEF
• 5 General Purpose Input / Output Pins (1 reserved for Reset required for programming)
• 32 General Purpose working Registers
• Tiny Size, Dimensions 25mm x 24mm x 4mm

The Digispark Kickstarter is an ATtiny85 based microcontroller development board similar to the line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark Kickstarter is a great way to jump into electronics, or perfect for when FOR Arduino is too big or too much.

The Digispark Kickstarter is an ATtiny85 based microcontroller development board similar to the line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark Kickstarter is a great way to jump into electronics, or perfect for when FOR Arduino is too big or too much.

ESP32-CAM ESP-32S WiFi Bluetooth Camera Module ESP32 serial to WiFi ESP32 CAM Development Board

ESP-32S Wifi Bluetooth combo Dev Kit is ultra high performance and ultra low-power consumption Wi-Fi and Bluetooth combo wireless platform based on ESPRESSIF ESP32 chipset. ESP-32S integrates dual-core processor, 448 KByte ROM,520 KByte S-RAM,16 KByte S-RAM in RTC, 802.11 b / g / n / e / I Wi-Fi, Bluetooth v4.2 BR/EDR & BLE, clocks & Times, abundant peripheral Interfaces and security mechanism.

• 100% New and High Quality LilyPad 328 Wearable Development Board
• Using Original Atmel ATmega328P-AU Microcontroller Chip IC
• Operating Voltage: 4.5 - 5.5V
• Digital I/O Pins: 14 (of which 6 provide PWM output)
• Analog Input Pins: 8
• Flash Memory: 32 KB of which 2 KB used by bootloader.
• SRAM: 2 KB.
• EEPROM: 1 KB.
• Clock Speed: 16 MHz.
• Uses: Smart car, smart home,Great for DIY projects
• Size: 50mm outer diameter, 0.8mm Thin

• ESP8266 microcontroller NodeMCU Lua V3 WIFI with CH340G
• Great for IOT (Internet Of Things) Projects
• Compatible with the Arduino IDE
• WiFi at 2.4GHz, support WPA / WPA2 security mode
• Support UART / GPIO data communication interface
• Remote firmware upgrade (OTA)
• 4MByte built-in Flash Memory

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IOT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won't need to buy a separate breakout board, USB to serial adapter, or even solder it to a bread board to get started, you will only need a USB cable (Micro USB).

• ESP8266 microcontroller NodeMCU Lua V3 WIFI with CP2102
• Great for IOT (Internet Of Things) Projects
• Compatible with the Arduino IDE
• WiFi at 2.4GHz, support WPA / WPA2 security mode
• Support UART / GPIO data communication interface
• Remote firmware upgrade (OTA)
• 4MByte built-in Flash Memory

• 100% New and High Quality WeMos D1 Mini Development Board
• Using Original ESP8266 ESP-12F Wifi and CH340G USB to UART Chip
• 11 Digital input / output pins
• All pins have interrupt / pwm / I2C / one-wire supported (except D0)
• 1 Analog input (3.2V max input)
• Micro USB Connection
• Compatible with Arduino
• Compatible with NodeMCU